fadercore_-_vlr-8odisp
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionNext revisionBoth sides next revision | ||
fadercore_-_vlr-8odisp [2014/07/24 15:11] – novski | fadercore_-_vlr-8odisp [2014/11/07 19:14] – Added info about BEB RTPMIDI CORE PCB novski | ||
---|---|---|---|
Line 1: | Line 1: | ||
- | ====== | + | [[fadercore_-_fadermodule_for_audio_daw|Fadercore]] |
+ | Standard 220mm wide Modules | ||
===== VLR-8oDisp ===== | ===== VLR-8oDisp ===== | ||
Line 6: | Line 7: | ||
A PCB for chaning up to 32 OLEDs on 4x8 OLED Modules. | A PCB for chaning up to 32 OLEDs on 4x8 OLED Modules. | ||
+ | It can be connected to the RTPMIDI-CORE-STM32F4 from BEB DigitalAudio. The Thread about that cool piece of Hardware is here: http:// | ||
+ | And you can Order his parts directly over his contact formula on the site: | ||
{{: | {{: | ||
Line 12: | Line 15: | ||
{{: | {{: | ||
- | |||
- | {{: | ||
{{: | {{: | ||
Line 21: | Line 22: | ||
Allways look for the cheapest seller, the Price may vary heavy!!! | Allways look for the cheapest seller, the Price may vary heavy!!! | ||
- | And look for Local dealers preferred. | + | And look for Local dealers preferred. |
+ | |||
+ | == The OLEDs == | ||
I got those displays from this dealer: http:// | I got those displays from this dealer: http:// | ||
- | ==== The other Materials: Mouser | + | == The other Materials: Mouser == |
* 2x10pin Header, 517-30310-6002 | * 2x10pin Header, 517-30310-6002 | ||
* 1x16pin Header, 517-30316-6002 | * 1x16pin Header, 517-30316-6002 | ||
- | * 2x8Pin | + | * 2x16Pin |
* 1xResistor Array 220Ohm, 652-4116R-1LF-220 | * 1xResistor Array 220Ohm, 652-4116R-1LF-220 | ||
* 1x74HC595, 595-SN74HC595N | * 1x74HC595, 595-SN74HC595N | ||
Line 38: | Line 41: | ||
Project Order Basket on Mouser: [[http:// | Project Order Basket on Mouser: [[http:// | ||
+ | |||
+ | The PCB is available under: [[https:// | ||
+ | |||
+ | ==== How to get Started ==== | ||
+ | |||
+ | You will need to set the Connection of the Display. | ||
+ | |||
+ | {{: | ||
+ | |||
+ | So all 3 Code Resistors need to be on the Left side... | ||
+ | |||
+ | If you don't like the LED on top you can de-solder it now. | ||
+ | |||
+ | ==== Prepare the PCB ==== | ||
+ | |||
+ | The first PCB gets its Selection Lines from the Display Connection J15A on the Core PCB. So you will need to solder the 16Pin Header at this Panel. Here you can leave out the 10pin Headers and the IC Socket for the Shift register, if you like. | ||
+ | |||
+ | The Second PCB for Display 9-16 gets its Selection lines from the Shift register and doesn' | ||
+ | |||
+ | For both use cases you need to stuff the Resistor array so its best to solder a 16pin IC-Socket and stuff it in that. | ||
+ | |||
+ | PCB 3&4 are same as the second. | ||
+ | |||
+ | {{: | ||
+ | |||
+ | ==== Prepare the Connection ==== | ||
+ | |||
+ | How to connect it to the Core | ||
+ | |||
+ | {{: | ||
+ | |||
+ | ==== Test it in MIOS ==== | ||
+ | |||
+ | This is a Test file for Mios:\\ | ||
+ | \\ | ||
+ | RESET_HW\\ | ||
+ | \\ | ||
+ | LCD " | ||
+ | LCD " | ||
+ | LCD " | ||
+ | LCD " | ||
+ | LCD " | ||
+ | LCD " | ||
+ | LCD " | ||
+ | LCD " | ||
+ | LCD " | ||
+ | LCD " | ||
+ | LCD " | ||
+ | LCD " | ||
+ | LCD " | ||
+ | LCD " | ||
+ | LCD " | ||
+ | LCD " | ||
+ | LCD " | ||
+ | LCD " | ||
+ | LCD " | ||
+ | LCD " | ||
+ | LCD " | ||
+ | LCD " | ||
+ | LCD " | ||
+ | LCD " | ||
+ | LCD " | ||
+ | LCD " | ||
+ | LCD " | ||
+ | LCD " | ||
+ | LCD " | ||
+ | LCD " | ||
+ | LCD " | ||
+ | LCD " | ||
+ | LCD " | ||
+ | \\ |
fadercore_-_vlr-8odisp.txt · Last modified: 2014/11/07 19:15 by novski