pickit2
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionLast revisionBoth sides next revision | ||
pickit2 [2009/01/24 16:09] – chr0n1c | pickit2 [2011/08/29 08:05] – maloneypark | ||
---|---|---|---|
Line 1: | Line 1: | ||
- | HOWTO PROGRAM A PIC18f452 WITH A PICKIT2 | + | ====== **HOWTO PROGRAM A PIC18f452 WITH A PICKIT2** ====== |
- | This page is here in hopes of helping somone else avoid having to go through what i did in figuring it all out. | + | |
+ | //This page is here in hopes of helping somone else avoid having to go through what i did in figuring it all out.(--chr0n1c)// | ||
The Pickit2 USB Programmer WILL generate the required voltages for HVP programming of the chip. | The Pickit2 USB Programmer WILL generate the required voltages for HVP programming of the chip. | ||
Line 7: | Line 8: | ||
It is possible to program you midibox core pic chip with this adapter and a Pickt2 from Microchip by following these steps. | It is possible to program you midibox core pic chip with this adapter and a Pickt2 from Microchip by following these steps. | ||
- | 1. BUILD THIS ICSP ADAPTER | + | **1. BUILD THIS ICSP ADAPTER** |
In order to do HVP with this circuit, you will need to short | In order to do HVP with this circuit, you will need to short | ||
the jumper going to pin 38 of the pic18f452. | the jumper going to pin 38 of the pic18f452. | ||
...will insert my schematic schreenshot here when i can get the uploader to work. | ...will insert my schematic schreenshot here when i can get the uploader to work. | ||
+ | |||
+ | |||
until then it's attached to these forum posts: | until then it's attached to these forum posts: | ||
| | ||
| | ||
| | ||
- | 2. PLUG IN YOUR PICKIT2 TO YOUR PC VIA USB. | + | **2. PLUG IN YOUR PICKIT2 TO YOUR PC VIA USB.** |
- | 3. CONNECT THE PICKIT2 TO THE ADAPTER YOU BUILT IN STEP 1. | + | **3. CONNECT THE PICKIT2 TO THE ADAPTER YOU BUILT IN STEP 1.** |
pin one of the pickit2 is the pin marked with a small triangle, | pin one of the pickit2 is the pin marked with a small triangle, | ||
align this with your adapters icsp header' | align this with your adapters icsp header' | ||
- | 4. INSERT YOUR PIC18f452 IN THE ADAPTER' | + | **4. INSERT YOUR PIC18f452 IN THE ADAPTER' |
pin 1 of the ic socket will be connected to pin 1 on the pickit2 for a ref. point. | pin 1 of the ic socket will be connected to pin 1 on the pickit2 for a ref. point. | ||
- | 5. start the pickit2 upload app. that you should already have installed from your pickit2 | + | **5. start the pickit2 upload app.** |
+ | you should already have installed | ||
| | ||
- | 6. load the most current bootloader file | + | **6. load the most current bootloader file** |
LINK TO THE MIOS DOWNLOADS PAGE: http:// | LINK TO THE MIOS DOWNLOADS PAGE: http:// | ||
| | ||
- | 7. CLICK THE UPLOAD HEX FILE BUTTON IN THE PICKIT2 APP. | + | **7. CLICK THE UPLOAD HEX FILE BUTTON IN THE PICKIT2 APP.** |
- | 8. once the software tells you it's done, click verify. | + | **8. once the software tells you it's done, click verify.** |
- | 9. PULL THE CHIP FROM THE PROGRAMMING ADAPTER AND INSERT IT TO YOUR MBHP_CORE. | + | **9. PULL THE CHIP FROM THE PROGRAMMING ADAPTER AND INSERT IT TO YOUR MBHP_CORE.** |
- | 10. from here, there is plenty of other documents on the wiki describing the next steps... | + | **10. from here, there is plenty of other documents on the wiki describing the next steps...** |
LINK: http:// | LINK: http:// | ||
Line 45: | Line 49: | ||
http:// | http:// | ||
http:// | http:// | ||
+ | [[http:// | ||
pickit2.txt · Last modified: 2011/09/16 23:47 by dougster