ssm2164_getting_started
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionNext revisionBoth sides next revision | ||
ssm2164_getting_started [2018/04/23 13:53] – [Resistor Solution low voltage - seppomans prefered] phatline | ssm2164_getting_started [2018/04/26 17:05] – [Class AB] phatline | ||
---|---|---|---|
Line 1: | Line 1: | ||
- | ======= ssm2164_seppoman pcb - getting started - how to setup ======= | + | ======= ssm2164_seppoman pcb introduction |
+ | seppomans building information; | ||
the following informations are take from the midibox forum, its a collection of infos, without the claim to be 100% true, i will try to test the given information. | the following informations are take from the midibox forum, its a collection of infos, without the claim to be 100% true, i will try to test the given information. | ||
Line 43: | Line 44: | ||
==== Resistor Solution low voltage - seppomans prefered ==== | ==== Resistor Solution low voltage - seppomans prefered ==== | ||
**R9...R16 > 5.6k** (only on the channels that are setup for bipolar mode)\\ | **R9...R16 > 5.6k** (only on the channels that are setup for bipolar mode)\\ | ||
- | **+-3.5V to +-5.8V** Bi-Polar calibration range | + | **+-3.5V to +-5.8V** Bi-Polar calibration range\\ |
**Pro:** easy job, still have a decent precision when calibrating.\\ | **Pro:** easy job, still have a decent precision when calibrating.\\ | ||
**Con:** “just change the jumpers if you need some channel in bipolar mode” thought will not work. (FIXME really?) | **Con:** “just change the jumpers if you need some channel in bipolar mode” thought will not work. (FIXME really?) | ||
- | ==== Resistor Solution Stock - NorthernLightX prefered ==== | + | ==== Resistor Solution Stock - -5V Level shifter |
we came to the conclusion that it's probably much easier to have the AOUT only output **unipolar 0 to 10 volt**, and design **a simple -5v level shifter board** that can be used as an add-on (or separate module with hands-on access to the level shifting) to **shift the output to -5 to +5 volt** where needed.\\ | we came to the conclusion that it's probably much easier to have the AOUT only output **unipolar 0 to 10 volt**, and design **a simple -5v level shifter board** that can be used as an add-on (or separate module with hands-on access to the level shifting) to **shift the output to -5 to +5 volt** where needed.\\ | ||
Line 66: | Line 67: | ||
**Pro:** preserve the "just change the jumpers if you need some channel in bipolar mode" thought behind this option.\\ | **Pro:** preserve the "just change the jumpers if you need some channel in bipolar mode" thought behind this option.\\ | ||
**Con: | **Con: | ||
+ | |||
+ | |||
+ | ====== MODs ====== | ||
+ | ===== MODE Resistor - Noise vs Distortion ===== | ||
+ | SSM2164 Pin 1 (the first pin) sets the " | ||
+ | ==== Class AB ==== | ||
+ | Pin 1 is Open, no Resistor to +12V (PCB Default)\\ | ||
+ | Lower current results in higher distortion/ | ||
+ | ==== Class A ==== | ||
+ | Pin 1 is Connected to +12V via a Resistor\\ | ||
+ | Higher current results in lower distortion/ | ||
+ | lets look in the datasheet: | ||
+ | {{: | ||
+ | Figures 11 and 12 show the THD and noise performance of the | ||
+ | SSM2164 as the bias current is adjusted\\ | ||
+ | |||
+ | I_MODE = ( (V+)−0.6V )/ RB\\ | ||
+ | 1,52mA = (12V-0.6V) / 7,5K\\ | ||
+ | Leaving the MODE pin open sets the SSM2164 in Class AB with 30 μA in the Gain-Core\\ |
ssm2164_getting_started.txt · Last modified: 2018/04/26 19:28 by phatline