loopa-eurorack-panel
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
loopa-eurorack-panel [2022/01/16 07:51] – [LoopA - Eurorack - Frontpanel with breakout PCB] phatline | loopa-eurorack-panel [2022/02/24 21:27] (current) – phatline | ||
---|---|---|---|
Line 3: | Line 3: | ||
{{: | {{: | ||
+ | {{youtube> | ||
**I made this Breakout-PCB and Frontpanel for the midiphy LoopA [[https:// | **I made this Breakout-PCB and Frontpanel for the midiphy LoopA [[https:// | ||
Line 15: | Line 16: | ||
ON this board we have 3 micromatch Connectors, which are crimped fast on a cable\\ | ON this board we have 3 micromatch Connectors, which are crimped fast on a cable\\ | ||
On the other side of the cable you have to solder directly to the Base-PCB,\\ | On the other side of the cable you have to solder directly to the Base-PCB,\\ | ||
- | be carefull while soldering - and follow the shematic, which is 3.5 Jack Midi Type B!\\ | + | be carefull while soldering - and follow the shematic, which is layout for 3.5 Jack Midi Type B!\\ |
{{: | {{: | ||
{{: | {{: | ||
Line 26: | Line 27: | ||
====== Building and BOM====== | ====== Building and BOM====== | ||
- | All necessery is printet on the PCB, but also check the Shematic...\\ | + | All necessery |
- | 8x 1Row 7Pin headers (2.54mm pitch)\\ | + | 5x [[https:// |
- | 8x 1K 1208 SMD Resistors\\ | + | 3x [[https:// |
- | 12x 10uF 1208 Capacitors (non polarized)\\ | + | 6x [[https:// |
- | 3x 10K 0603 SMD Resistors which are optional\\ | + | 1x [[https:// |
- | {{:phatline:LRE-OLED-BAR-3D-Back.jpg?700|}}\\ | + | 1x [[https:// |
+ | 8x [[https:// | ||
+ | 12x [[https:// | ||
+ | 4x [[https:// | ||
+ | \\ | ||
+ | And there will be some additional Fasting Material, like bolts, Screws, Standoffs, that i dont know right now, because the first protoype has to be built first...\\ | ||
====== Frontpanel====== | ====== Frontpanel====== | ||
- | {{: | + | {{: |
- | I made a DXF File which you can send to [[https:// | + | **I made a DXF File which you can send to:** (once the prototypestate is gone)\\ |
- | + | [[https:// | |
- | i panalized it so there are 2 Plates | + | [[https:// |
- | I payed 40€ summed for booth plates incl shipping from Germany to Austria\\ | + | [[https:// |
- | {{:phatline: | + | [[https:// |
+ | \\ | ||
**Recommend Material**\\ | **Recommend Material**\\ | ||
- | 3mm x 128.5 x 188.58 Aluminium, anodised)\\ | + | 2mm x 128.5 x 188.58 Aluminium, anodised\\ |
+ | contact frontpanels: | ||
+ | {{: | ||
+ | ====== Interconnection to LoopA ====== | ||
+ | To most connections are Midi... so before start, take a look at some standards: | ||
+ | {{: | ||
====== To Do ====== | ====== To Do ====== |
loopa-eurorack-panel.1642319511.txt.gz · Last modified: 2022/01/16 07:51 by phatline