midibox_lc
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
midibox_lc [2006/10/15 09:35] – (old revision restored) 127.0.0.1 | midibox_lc [2016/08/05 17:58] (current) – ↷ Links adapted because of a move operation 192.243.55.130 | ||
---|---|---|---|
Line 5: | Line 5: | ||
===== Which modules do I need for Midibox LC? ===== | ===== Which modules do I need for Midibox LC? ===== | ||
- | * 1x core module with PIC18F452 | + | * 1x [[core module]] with PIC18F452 |
- | * 1x graphic LCD (240×64 of pixels) or 2 characters LCDs (2×40 characters) | + | * 1x graphic LCD (240×64 of pixels) or 2 characters LCDs (2×40 characters) or 2 GLCDS (2x 128X64) |
* 4x DINX4 module for 96 switches | * 4x DINX4 module for 96 switches | ||
* 3x DOUTX4 module for LED rings and LEDs | * 3x DOUTX4 module for LED rings and LEDs | ||
* 1x LTC module | * 1x LTC module | ||
- | * 1x MF module | + | * 1x [[mf_ng_module]] |
If not "in main.asm, you have to set " | If not "in main.asm, you have to set " | ||
Line 25: | Line 25: | ||
* 8x Motorfader or Faders | * 8x Motorfader or Faders | ||
- | ===== Do I have to build the PCBs for themselves? ===== | + | |
+ | ===== Do I have to build the PCBs by myself? ===== | ||
No. Look here [[http:// | No. Look here [[http:// | ||
- | ===== How do I configure the DIN and Douts for my Switches, Encoder and LEDS? ===== | + | |
+ | ===== How do I configure the DINs and DOUTs for my Switches, Encoder and LEDS? ===== | ||
* Switches and LED in lc_io_table.inc, | * Switches and LED in lc_io_table.inc, | ||
* Encoders in mios_tables.inc | * Encoders in mios_tables.inc | ||
Line 34: | Line 36: | ||
===== Why does the value of the Encoder change automatically after few seconds, even when nothing is touched? ===== | ===== Why does the value of the Encoder change automatically after few seconds, even when nothing is touched? ===== | ||
That can happen, if no Motorfader is attached. In main.asm set the ENABLE_MOTORDRIVER flag to the value set 0, afterwards this effect should disappear. | That can happen, if no Motorfader is attached. In main.asm set the ENABLE_MOTORDRIVER flag to the value set 0, afterwards this effect should disappear. | ||
+ | |||
+ | |||
===== Can I replace the Encoders with normal potentiometers to save money? ===== | ===== Can I replace the Encoders with normal potentiometers to save money? ===== | ||
- | No, in the Logic/ | + | No, in the Logic/ |
+ | " | ||
+ | This means that the midibox sends a signal | ||
+ | If you use a potentiometer, | ||
+ | Check out [[encoders]] for specifications and where to order. | ||
+ | |||
+ | ===== I want to build a Mackie C4 type box, does the MBLC do this? ===== | ||
+ | No.\\ | ||
+ | That is, not yet.\\ | ||
+ | There is nothing to prevent a Midibox LC/C4 box from working, but some research needs to be done. | ||
+ | When Mackie made the LC, and then the MCU, they made the protocol public. This was // | ||
+ | Short answer: Now is your time to step up and do this research. Make the C4 possible, and win the adoration of your peers! | ||
===== Your Turn ===== | ===== Your Turn ===== | ||
Ok, I know this isnt the entire German version but [[http:// | Ok, I know this isnt the entire German version but [[http:// | ||
+ | |||
+ | |||
+ | |||
+ | ====== How to build a display and meter unit for Tascam US2400 and Nuendo ====== | ||
+ | |||
+ | Dietmar wrote an interesting HowTo for using MBLC as display and meter unit for Nuendo - the controllers (Motorfaders/ |
midibox_lc.1160904901.txt.gz · Last modified: 2007/07/16 20:36 (external edit)