), but all other settings such as length, divider value, name etc. are reset to default values.
By defau... doesn't take normal notes as input, but instead a value from A-P to a-p (plus octave value from 0 to 3), each of which represents a pre-defined chord. The list ... m length to 256 steps. A disadvantage is that the value names don't make musical sense, though the names
the event is handled - On/Off, Tap Tempo, Link to value map, etc There are 9 types to choose from (we'll look at these later). \\
2. 10x Value Maps \\
These maps contain named values (paramet... or anything that has a name associated with it's value.
When using a CC linked to a value map, instead of seeing meaningless numbers, it will show the name of
igned int i;
unsigned int pin = 0;
unsigned int value = 0;
unsigned int value2 = 0;
// poll Timer()
if(debug_user_timer.TIMER_ENABLED) {
Timer();
}
// ... LSE;
break;
case ' ': // OK
debug_din_value[DEBUG_BUTTON_OK] = 0;
DIN_NotifyToggle(DEBUG_BUTTON_OK, debug_din_value[DEBUG_BUTTON_OK]);
break;
case '+': // E
}
</wrap>
===== Parts List =====
^Part ^Value ^Type ^ Qty ^ Mouser Ref ^
|... hardware manual lists the sounds created by each value, some experimentation will be necessary to find "... 50%>
{{:tia-stella_audcx.png?1000|AudCx registers value}}\\
</WRAP>
<WRAP column 40%>\\
\\
\\
\\
\\
These... it audio frequency register (AUDF0, AUDF1).\\
The value written is used to divide a 30KHz reference frequ
- buttons (preset / bus / input / output)
* 16 "value-buttons"
* 16 presets
* 16 buses
* ultra-fl... tch to a screen by pushing the screen button, the value button LED's reflect the setup for this screen, w... reset screen** is the top-level-screen. Pushing a value button loads a preset (1-16). Pushing [preset]+[X... can be added/removed from a bus. Pushing a single value button again will switch off the other values, an
ol Patch names, Gig Control List names and Device value maps
**Parameter** - Used by Device value maps to define mid parameter 2.
**Status** - NO LONGER USED
... to define what event should be triggered.
**Low Value** - AIN and DIN maps to define the lowest value to be sent.
**High Value** - Used by Rig Control, AIN a
tech/midispec/vol.htm|Volume]], Control Change 7, value range 0-127.\\
[[http://home.roadrunner.com/~jggl... midispec/balance.htm|Balance]], Control Change 8, Value range 1-64-127.\\
[[http://home.roadrunner.com/~j... t/tech/midispec/pan.htm|Pan]], Control Change 10, Value range 1-64-127.\\
[[http://home.roadrunner.com/~j... midispec/exp.htm|Expression]], Control Change 11, value range 0-127\\
[[http://home.roadrunner.com/~jggla
fast bitshifting or complex division depending on value
* AUTO-sense feature: **auto-calibration** of s... ions are possible
* **detect release**: send 0-value if signal drops below sense-min
* slowdown: slo... Red Button | STORE PATCH |
| | Left Encoder | Value setter for selected menu item / parameter 1 |
| | Right Encoder | Value setter for selected menu item / parameter 2 |
|
4 are used for notes.
- Channel 1: Gate 1, Note Value -> CV 1, VEL Value -> CV 2
- Channel 2: Gate 2, Note Value -> CV 3, VEL Value -> CV 4
- Channel 3: Gate 3, Note Value -> CV 5, VEL Value -> CV 6
- Channel 4: G
nd -. Pushing F1 and F7 will change the transpose value (TR1). For the UPPER Keyfield TR2 is adjustable i... eel of K64. CC Values are sended out by moving CC Value up and down with that keys. INST/DEL Key sets val... s in a specific interval up and down. Close to CC Value area, there are 2 marker adjustable. The Startpoi... changing end- and start-position and setup Speed Value.
Start Marker:
{{http://www.inventati.org/ganch
can display tap tempo rate, or even the name of a value for a control - eg. For an Amp model select CC, i... sent based on the Rig COntrol Patch Change
* Value scaled between pre-defined min and max values (ca...
* Named CC events
* Bar Graph displaying value/on/off
* up to 10 specific CC value name tables for effect selection, etc
* Tap Tempo BPM displa
ssage contains 2x 7bits of info: CC Number and CC Value.
* CC Number controls which "bank" of 7 FXs is being controlled.
* CC Value controls the 7 FX of one bank = one FX "bank".
* 2x 7 bits for controller number and value = 14 bits => 127 FX banks, each consisting of 7 F... Change message can be done "binary" using the CC value:\\
* Midi CC0 0 = 000 0000 = all FX OFF (= a
all AOUT channels need to be updated with each CV value change. Be aware that matching and soldering all ... =====
\\
^Name ^Part ^Value ^Quantity ^Reichelt Order Code ^Mouser^
|**Regul... his is necessary to get access to the full output value range. Set all jumpers to unipolar mode (see **Co... menu of the MBSID patch. You'll see a 3 digit hex value indicating the current output value for each chan