WingMa
-
Posts
59 -
Joined
-
Last visited
Content Type
Profiles
Forums
Blogs
Gallery
Posts posted by WingMa
-
-
Hello,
I thinking about LED ring Matrix... If my first ledring at 100 so all 11 LED bright, how can I set the second LED ring to 20 % with two LEDs!
With first Ring all catode on, so I switch de second anode all LED bright???
-
I aborted my order! Wich to continue to lpc 19 rev d or new STM32?
-
I can’t find rev d on market just one rev c
-
Ucapps have no info on rev c
-
Ok I bought an rev c, all side legs need to connect? And the end the hole 19 is free or need to solder somewhere?
-
And the Bootloader Work as the original?
-
Just now, FantomXR said:
Why are you afraid to the modification, that is suggested on Rev C models (bending the legs)?
And for the STM: You can get the PCBs herhttps://modularaddict.com/manufacturer/midibox/midibox-core-stm32-pcb
Somebody tell me Rev C not fit competelly. If its only leg modifications I can do it
-
Hello,
Does anybody have a for saled core bacause my LPC is dead I only can buy rev C what not fit to my pcb.
I have four Din/Dout model two Motofader Board But have no core!
If sombod know a shop or have an unnecessary core please write me!
For me good The STM32 too.
I am very bitter!
Regards:
Bela
-
-
-
On 2/19/2017 at 0:43 AM, Highcooley said:
after a couple of hours going exactly through these steps myself, tripping over exactly the same stumbling blocks and figuring out exactly the same solutions, I find your post ...face palming myself. But at least I can confirm, that it indeed works after a lot of pin bending and ramming the board onto the headers. I also soldered a short wire for the two Ethernet LEDs onto the left side of LED3 and 4. The network connector ones lit up, but only dimly. I guess, I should have done that either onto the right side of the SMD LED's or onto the left side of the corresponding resistors on the LPCxPresso board. But here is how I did it:
By the way, that's how the headers had to be bent in order to be able to give them a firm push to fit them onto the headers:
...and I can confirm that the Rev D board actually works with all the midibox bells an whistles (I'm using it with DIO, AIO, SCS, standard 2xmidi IO, USB, Ethernet and a single GLCD).
Hy
This is the rev D?
Only this modification I need to use?
And bootloader work with this?
Thanks
-
I expecting your zen years experience...
-
Just now, latigid on said:
Buy one, try it and report back.
Yes I am a millionaire... If not work go to trash and buy other... Fantastic
-
Please read the MA lighting forum! You have a question 10 minutes and get the complete solution for me or other... I’m not a robot engineer but need your project but I can’t do it alone
-
37 minutes ago, FantomXR said:
C doesn't fit.
D: no experience with it.
Totally no fit or just the end part?
-
I seat at my bed and reading all of ucapps all of forum and wait your or forum answers but nothing! Motor board maybe ok but I have core without brain because now can’t buy the original? My question: what can I do? Answer: what I finded is not fit other no experience! So what can I do now?
-
I have more the 1000 euro in this project, i thing not so much my question, I need help after ten years I was lagging! And the forum somebody write this the other write other I need the workable...
-
Ok it’s diy project but why can do together??? Yours work my is with so many fault..
-
I don’t think you are right! I bought something before ten years after this so many changes! I have time but I think easier if somebody go away that what I stopped, simple write her/him experience! I have 3 different board with so many question but no answer! I am so many forum and if I have answer don’t sorry the time and share my experience... We are different it’s ok but I have 3 topic and 2 half answer is not to much! I have tour and I would like to proceed but not help for experied pepople! It so strong to write 2 rows about my questions?
-
Please somebody tell me C or D???
-
And thank your answers I’m really
gratefull ;) This forum a bit died...
-
And in software set the two pot same?
-
On 2016. 09. 16. at 10:45 AM, monokinetic said:
Interesting, I didn't know that. I have one more LPC core that I plan to stuff. Does anyone happen to know if LPC1769 revision D, currently available on the embeddedartists site, is compatible with LPC core? They claim that:
"the expansion pins (2x27 positions) are mechanically compatible with the original design"
but I'd like to check if anyone here has experience with it before I order.
Or buy this D because it’s better than C?
-
Other size is same?
Available Core
in Latest News
Posted · Edited by WingMa
Hi Guys,
Can you tell me somebody wich core are completely available???
I have so many din dout module but not have core what can I control this element…
i have this pcb but I don’t know what type of module need to buy to this
Mbhp_core_lpc17_v1
i need a link where can I buy the lpcxpreso
Otherwise: Which is the best full stable core what I can built now?
I need one core!!!
I have dinx4_V2 and doutx4_V2
Thanks