Jump to content

Build your own tools


artyman
 Share

Recommended Posts

Hi,

As the plans for my (upcoming) MBLC required a lot of CNC work doing, I thought to myself... Why not build one?

So... several hours of internet browsing later, and jaw-dropping of the prices of kits, I started out to design my own to the size i wanted.

The design spec was simple - to be able to rout a panel the size of a 6u rack panel.

The process of sourcing parts began, from various sources, Ebay being the most prominent, and the design started.

Being on a tight budget, the most expensive parts - lead screws and ballnuts were replaced with standard threaded bar and a clever arrangement of wood block and threaded inserts to reduce backlash.

Now building it starts...

Beginning with the z-axis and gantry:-

post-7782-0-54814600-1349503827_thumb.jp

post-7782-0-81823300-1349503840_thumb.jp

post-7782-0-41003900-1349503847_thumb.jp

post-7782-0-40885900-1349503858_thumb.jp

post-7782-0-97083600-1349503871_thumb.jp

post-7782-0-42060100-1349503883_thumb.jp

post-7782-0-48904500-1349503889_thumb.jp

post-7782-0-36523000-1349503913_thumb.jp

post-7782-0-46980300-1349504186_thumb.jp

post-7782-0-86534100-1349504188_thumb.jp

post-7782-0-72189500-1349504191_thumb.jp

post-7782-0-56010400-1349504195_thumb.jp

post-7782-0-40040000-1349504198_thumb.jp

post-7782-0-97485400-1349504200_thumb.jp

Edited by artyman
Link to comment
Share on other sites

I was going to order a kit from America at a cost of around $500 how does this compare with your costs?

Looking good by the way.

cheers

Paul

edit ...I just noticed you are in leeds..................better make sure it's locked up safe at night as I am in Sheffield :)....joking

Edited by taximan
Link to comment
Share on other sites

Thank you

It's a steady process having to cut and drill each piece accurately, and believe it or not... I've only had to re-make 1 piece!!

The advantage of a kit is that 90% of the hard work has been done, it only has to be assembled. The disadvantage is that there's limited options on what size machine you can build, I've built mine to fit the space I have.

Mine has cost me somewhere in the region of £250-300 so far, and there's still some bits to buy... e.g. drag chains to keep the cabling tidy, and channel for it to lay into. I'm expecting the total cost to be about £300.

btw, I used to live in Sheffield... went to University there.

Rob

@ rosch.. cheers, if this turns out to be accurate enough, I may be able to do the odd midiboxer a favour or 2. :wink:

Link to comment
Share on other sites

Yes, you are right that aluminium would be more long lasting, but I've done a LOT of online research into this and most DIY CNC kits and plans use wooden frames, so it's not an un-viable option.

I don't see any reason why a wooden-framed CNC should be less accurate than an aluminium framed one. Built correctly, a wooden frame can be perfectly stiff enough to satisfy the needs of lightweight CNC work.

The other reason I decided on a wood frame was cost - as I don't have the tools to machine the sort of size pieces needed, I would have had to get them custom made, which would more than double the price tag.

Link to comment
Share on other sites

The Z-axis is now threaded up, and the slider is moving smoothly :frantics:

The gantry (X-axis) now has the bottom brace fitted and is ready to have the Z-axis mounted, and also start fitting to the base section.

Next job is the motor mounts... make all 3, and fit to the Z-axis, and then the X-axis, once the z-axis assembly is mounted and moving smoothly.

post-7782-0-77817500-1349734031_thumb.jp

post-7782-0-12767700-1349734079_thumb.jp

post-7782-0-37987300-1349795240_thumb.jp

post-7782-0-95640300-1349795242_thumb.jp

post-7782-0-41505600-1349795246_thumb.jp

Edited by artyman
Link to comment
Share on other sites

Test fitting of the gantry assembly to the baseboard, mainly to check my marking out is good before drilling.

All is as planned there, and the gantry runs smoothly on it's rails.

next was a dry fit of the rest of the base assembly, and clearances are looking good there.

time now to drill all the bolt holes , including a 9x6 grid on the table to fit 54 t-nuts, for clamping points.

post-7782-0-16503100-1350409012_thumb.jp

post-7782-0-13888200-1350409019_thumb.jp

Link to comment
Share on other sites

I'm not sure how well it will perform with metals, though I'm hoping it will be able to cut Aluminium and Brass.

It will be the subject of some very careful experimentation. :thumbsup:

@Hawkeye - thank you, I'm hoping all the effort will be worth it.

Edited by artyman
Link to comment
Share on other sites

  • 3 weeks later...

Well.. after a busy period at work, and looking for a 'new' car, I find myself back on leave, and time to do some more work on this.

Now that I've dry fit the pieces of the base section, it's time to drill and bolt everything down.

Also at this time I've drilled a grid on the table and fitted T-nuts to the underside for screw-in clamps. Note also the 2 braces on the underside of the table to reduce any flexing.

These additions to the original design, fortunately were possible without interfering with the bottom brace of the gantry

EDIT

Also showing detail of the thrust bearings used on all of the lead screws.

post-7782-0-05799200-1352228006_thumb.jp

post-7782-0-87334300-1352228022_thumb.jp

post-7782-0-54480100-1352228029_thumb.jp

post-7782-0-80129600-1352293098_thumb.jp

Edited by artyman
Link to comment
Share on other sites

  • 3 weeks later...

Now that I have the microswitches, and the E Stop switch, it's time, with a little help from my daughter, to fit those.

The X and Y axes were an easy fit, One set screwed directly to the structure, and the other needed just a simple L-bracket to fit.

The Z axis, however was a bit more challenging. Although I got subminiature microswitches, they were too wide for direct actuation as the other axes are arranged, so a little inventive thinking was called for.

As I had roller actuators, I decided to cut chamfers on the Z-slider, and mount them inline. This also meant that i had to file a notch in the side wall so they wouldn't interfere with the tool mount (when fitted) as it passed over.

post-7782-0-07564400-1353875653_thumb.jp

post-7782-0-02760900-1353875729_thumb.jp

post-7782-0-46111600-1353875765_thumb.jp

post-7782-0-07303500-1353875791_thumb.jp

post-7782-0-91340400-1353875814_thumb.jp

post-7782-0-52735000-1353875838_thumb.jp

post-7782-0-79244000-1353875863_thumb.jp

post-7782-0-59922000-1353875901_thumb.jp

post-7782-0-04118500-1353875955_thumb.jp

Link to comment
Share on other sites

  • 4 weeks later...

Finally, after my busiest time of the year at work... I've managed to find time to fabricate the tool mount and fit my spindle.

 

I'm incredibly pleased... not only is the tool solid in the mount, but it's also perfectly perpendicular to the table !! :smile: :D :happy: :hyper:

 

Next step is to buy the full version of Mach3, then I can start cutting!!!

 

 

post-7782-0-38146300-1356988407_thumb.jp

post-7782-0-23180500-1356988413_thumb.jp

post-7782-0-68058100-1356988418_thumb.jp

Link to comment
Share on other sites

I like it very much! Good quality cuts! And with the thickness of the wood you managed to cut, I am quite sure, it would work on aluminum or thin carbon fibre plates, too!

 

The best thing is now, that you can reinforce parts of your CNC with its own self-made parts, if you think it is necessary... a self-improving machine - skynet is online :-).

 

Would you give us a short list of parts, ie. stepper motors/control logic kit used in your CNC?

 

Many greetings!

Peter

Edited by Hawkeye
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...
 Share

×
×
  • Create New...