Jump to content

LED Matrix around 8 Encoders

novski

By novski,
in MIDIbox NG

 Share

Recommended Posts

novski MIDIbox Tweaker

novski

Posted
Posted

I have problems with my LED Matrix.

I built it upon the Schematic of Fairlightiii's pcb but with just 8 Encoders and LED Rings.

 

By turning one of the Encoders all LEDs around the other Encoders go on, but the LEDs around the Encoder i turn don't. 

And the brightness of the LEDs increase by Turning all the Encoders to 127.

 

Don't know where to start searching. 

The PCB is correct, i checked that. 

 

this ist my config .ngc for testing:

 

RESET_HW
LCD "%C"
LCD "@(1:1:8)OLED1"
LCD "@(2:1:8)OLED2"
LCD "@(3:1:8)OLED3"
LCD "@(4:1:8)OLED4"
LCD "@(5:1:8)OLED5"
LCD "@(6:1:8)OLED6"
LCD "@(7:1:8)OLED7"
LCD "@(8:1:8)OLED8"

# Buttons configuration

EVENT_BUTTON id=1   fwd_id=LED:1   type=NoteOn key=24  lcd_pos=1:1:1 label="^std_btn"
EVENT_BUTTON id=2   fwd_id=LED:2   type=NoteOn key=37  lcd_pos=2:1:1 label="^std_btn" 
EVENT_BUTTON id=3   fwd_id=LED:3   type=NoteOn key=38  lcd_pos=3:1:1 label="^std_btn" 
EVENT_BUTTON id=4   fwd_id=LED:4   type=NoteOn key=39  lcd_pos=4:1:1 label="^std_btn" 
EVENT_BUTTON id=5   fwd_id=LED:5   type=NoteOn key=40  lcd_pos=5:1:1 label="^std_btn" 
EVENT_BUTTON id=6   fwd_id=LED:6   type=NoteOn key=41  lcd_pos=6:1:1 label="^std_btn" 
EVENT_BUTTON id=7   fwd_id=LED:7   type=NoteOn key=42  lcd_pos=7:1:1 label="^std_btn"  
EVENT_BUTTON id=8   fwd_id=LED:8   type=NoteOn key=43  lcd_pos=8:1:1 label="^std_btn" 
EVENT_BUTTON id=9   fwd_id=LED:9   type=NoteOn key=36  lcd_pos=1:1:1 label="^std_btn"
EVENT_BUTTON id=10  fwd_id=LED:10  type=NoteOn key=37  lcd_pos=2:1:1 label="^std_btn" 
EVENT_BUTTON id=11  fwd_id=LED:11  type=NoteOn key=38  lcd_pos=3:1:1 label="^std_btn" 
EVENT_BUTTON id=12  fwd_id=LED:12  type=NoteOn key=39  lcd_pos=4:1:1 label="^std_btn" 
EVENT_BUTTON id=13  fwd_id=LED:13  type=NoteOn key=40  lcd_pos=5:1:1 label="^std_btn" 
EVENT_BUTTON id=14  fwd_id=LED:14  type=NoteOn key=41  lcd_pos=6:1:1 label="^std_btn" 
EVENT_BUTTON id=15  fwd_id=LED:15  type=NoteOn key=42  lcd_pos=7:1:1 label="^std_btn"  
EVENT_BUTTON id=16  fwd_id=LED:16  type=NoteOn key=43  lcd_pos=8:1:1 label="^std_btn"
EVENT_BUTTON id=17  fwd_id=LED:17  type=NoteOn key=36  lcd_pos=1:1:1 label="^std_btn"
EVENT_BUTTON id=18  fwd_id=LED:18  type=NoteOn key=37  lcd_pos=2:1:1 label="^std_btn" 
EVENT_BUTTON id=19  fwd_id=LED:19  type=NoteOn key=38  lcd_pos=3:1:1 label="^std_btn" 
EVENT_BUTTON id=20  fwd_id=LED:20  type=NoteOn key=39  lcd_pos=4:1:1 label="^std_btn" 
EVENT_BUTTON id=21  fwd_id=LED:21  type=NoteOn key=40  lcd_pos=5:1:1 label="^std_btn" 
EVENT_BUTTON id=22  fwd_id=LED:22  type=NoteOn key=41  lcd_pos=6:1:1 label="^std_btn" 
EVENT_BUTTON id=23  fwd_id=LED:23  type=NoteOn key=42  lcd_pos=7:1:1 label="^std_btn"  
EVENT_BUTTON id=24  fwd_id=LED:24  type=NoteOn key=42  lcd_pos=8:1:1 label="^std_btn" 
   
EVENT_BUTTON id=41   fwd_id=LED:41  type=NoteOn key=43  lcd_pos=1:1:2 label="^std_btn"
EVENT_BUTTON id=41   fwd_id=LED:25  type=NoteOn key=43  lcd_pos=1:1:2 label="^std_btn"
EVENT_BUTTON id=42   fwd_id=LED:42  type=NoteOn key=36  lcd_pos=2:1:2 label="^std_btn"
EVENT_BUTTON id=43   fwd_id=LED:43  type=NoteOn key=37  lcd_pos=3:1:2 label="^std_btn" 
EVENT_BUTTON id=44   fwd_id=LED:44  type=NoteOn key=38  lcd_pos=4:1:2 label="^std_btn" 
EVENT_BUTTON id=45   fwd_id=LED:45  type=NoteOn key=39  lcd_pos=5:1:2 label="^std_btn" 
EVENT_BUTTON id=46   fwd_id=LED:46  type=NoteOn key=40  lcd_pos=6:1:2 label="^std_btn" 
EVENT_BUTTON id=47   fwd_id=LED:47  type=NoteOn key=41  lcd_pos=7:1:2 label="^std_btn" 
EVENT_BUTTON id=48   fwd_id=LED:48  type=NoteOn key=42  lcd_pos=8:1:2 label="^std_btn"  

# Encoder configuration
ENC n=  1   sr=4 pins=0:1   type=detented2
ENC n=  2   sr=4 pins=2:3   type=detented2
ENC n=  3   sr=4 pins=4:5   type=detented2
ENC n=  4   sr=4 pins=6:7   type=detented2
ENC n=  5   sr=5 pins=0:1   type=detented2
ENC n=  6   sr=5 pins=2:3   type=detented2
ENC n=  7   sr=5 pins=4:5   type=detented2
ENC n=  8   sr=5 pins=6:7   type=detented2

# LEDring configuration
DOUT_MATRIX n= 1  rows=8 sr_dout_sel1= 7  sr_dout_sel2= 0 sr_dout_r1= 8 sr_dout_r2= 9

# Encoder events
EVENT_ENC id= 1  fwd_id=LED_MATRIX:1   type=CC chn= 1 cc= 24  lcd_pos=1:1:4 label="^std_enc"
EVENT_ENC id= 2  fwd_id=LED_MATRIX:2   type=CC chn= 1 cc= 25  lcd_pos=2:1:4 label="^std_enc"
EVENT_ENC id= 3  fwd_id=LED_MATRIX:3   type=CC chn= 1 cc= 26  lcd_pos=3:1:4 label="^std_enc"
EVENT_ENC id= 4  fwd_id=LED_MATRIX:4   type=CC chn= 1 cc= 27  lcd_pos=4:1:4 label="^std_enc"
EVENT_ENC id= 5  fwd_id=LED_MATRIX:5   type=CC chn= 1 cc= 28  lcd_pos=5:1:4 label="^std_enc"
EVENT_ENC id= 6  fwd_id=LED_MATRIX:6   type=CC chn= 1 cc= 29  lcd_pos=6:1:4 label="^std_enc"
EVENT_ENC id= 7  fwd_id=LED_MATRIX:7   type=CC chn= 1 cc= 30  lcd_pos=7:1:4 label="^std_enc"
EVENT_ENC id= 8  fwd_id=LED_MATRIX:8   type=CC chn= 1 cc= 31  lcd_pos=8:1:4 label="^std_enc"

# we've a single MBHP_MF_NG module with 8 motorfaders
# It has to be configured for Motormix protocol!

MF n=1  enabled=1  midi_in_port=IN2  midi_out_port=OUT2  chn=1  ts_first_button_id=2001  config_port=USB3

################################################################################

# on motorfader movements
EVENT_MF  id= 1  fwd_id=ENC:33  type=CC  chn= 1 cc=32  range=0:127  lcd_pos=1:1:5  label="^std_mf"
EVENT_MF  id= 2  fwd_id=ENC:34  type=CC  chn= 1 cc=33  range=0:127  lcd_pos=2:1:5  label="^std_mf"
EVENT_MF  id= 3  fwd_id=ENC:35  type=CC  chn= 1 cc=34  range=0:127  lcd_pos=3:1:5  label="^std_mf"
EVENT_MF  id= 4  fwd_id=ENC:36  type=CC  chn= 1 cc=35  range=0:127  lcd_pos=4:1:5  label="^std_mf"
EVENT_MF  id= 5  fwd_id=ENC:37  type=CC  chn= 1 cc=36  range=0:127  lcd_pos=5:1:5  label="^std_mf"
EVENT_MF  id= 6  fwd_id=ENC:38  type=CC  chn= 1 cc=37  range=0:127  lcd_pos=6:1:5  label="^std_mf"
EVENT_MF  id= 7  fwd_id=ENC:39  type=CC  chn= 1 cc=38  range=0:127  lcd_pos=7:1:5  label="^std_mf"
EVENT_MF  id= 8  fwd_id=ENC:40  type=CC  chn= 1 cc=39  range=0:127  lcd_pos=8:1:5  label="^std_mf"

# on touchsensor event (first id has been specified in the MF configuration above)
EVENT_BUTTON  id= 2001  type=NoteOn chn= 1 key=0x68  range=0:127  lcd_pos=1:1:6  label="^std_btn"
EVENT_BUTTON  id= 2002  type=NoteOn chn= 1 key=0x69  range=0:127  lcd_pos=2:1:6  label="^std_btn"
EVENT_BUTTON  id= 2003  type=NoteOn chn= 1 key=0x70  range=0:127  lcd_pos=3:1:6  label="^std_btn"
EVENT_BUTTON  id= 2004  type=NoteOn chn= 1 key=0x71  range=0:127  lcd_pos=4:1:6  label="^std_btn"
EVENT_BUTTON  id= 2005  type=NoteOn chn= 1 key=0x72  range=0:127  lcd_pos=5:1:6  label="^std_btn"
EVENT_BUTTON  id= 2006  type=NoteOn chn= 1 key=0x73  range=0:127  lcd_pos=6:1:6  label="^std_btn"
EVENT_BUTTON  id= 2007  type=NoteOn chn= 1 key=0x74  range=0:127  lcd_pos=7:1:6  label="^std_btn"
EVENT_BUTTON  id= 2008  type=NoteOn chn= 1 key=0x75  range=0:127  lcd_pos=8:1:6  label="^std_btn"

 

Any Ideas?

 

Thanks

novski

Link to comment
Share on other sites
TK. MIDIbox Guru

TK.

Posted
Posted

Sounds like an inverted selection.

 

Are you using ULN2803 as sink drivers?

Then you would have to use following configuration:

DOUT_MATRIX n= 1  rows=8  inverted_sel=1  sr_dout_sel1= 7  sr_dout_sel2= 0 sr_dout_r1= 8 sr_dout_r2= 9

 

Or you are not using an ULN2803, but the polarity of the LEDs is wrong?

Then try:

DOUT_MATRIX n= 1  rows=8  inverted_sel=1  inverted_row=1  sr_dout_sel1= 7  sr_dout_sel2= 0 sr_dout_r1= 8 sr_dout_r2= 9

 

Best Regards, Thorsten.

Link to comment
Share on other sites
novski MIDIbox Tweaker

novski

Posted
  • Author
Posted

Hi TK.

Wonderful! it was the Inverter... The Polarity is equal to fairlightiiis pcb.

But i designed just 15 LEDs because for Audio Panorama functionality i want a Middle "single" LED. 

Now the Middle point is decreased to left. I expected it to increase to right because the LED missing there. (my LEDs are like fairlightiii's from left to right) Is that because of the Inverting? 

Thanks a lot!

novski

Link to comment
Share on other sites
novski MIDIbox Tweaker

novski

Posted
  • Author
Posted

Do i understand right?

Mirroring = It lets the LEDs go "ON" in the opposite direction (shift-register Outputs go Low in Opposite direction as without)

Inverting = It swaps the row and selector shift registers

 

Best Regards

Novski

Link to comment
Share on other sites
TK. MIDIbox Guru

TK.

Posted
Posted

No, inverting means, that the signals on the DOUT output will be reversed.

Means: instead of 1, a 0 will be output, and instead of 0, a 1 will be output.

This is required for the case that somebody swapped anode/cathode of a LED, or to revert the polarity change of a sink driver.

 

Best Regards, Thorsten.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...
×
 Share
Go to topic listing
×
×
  • Create New...