Jump to content

Aout_NG Not working on midibox seqv4


flyweight
 Share

Recommended Posts

Hi Guys,

I am finaly near the end of my build of a seq4. Only need to have the Aout_ng and possible the D-out working. 
The D-out I will try to build on a breadboard for some extra gates and clocks.
Realy looking forward for the awesomeness of controlling a modular with the midibox.

Thanks again TK for bringing the AWESOME project to the public.

Would you have any idea what can be the issue here with my aout_ng? Does anything below indicate wrong wiring?

MBSEQ_GC.V4: "CV_AOUT_Type" and set it to 3 for AOUT_NG
And on the CV Configuration Page the aout_ng is set.

Core STM32F4 AOUT_NG on j19 Connected like

J1:1 -> J19:Vs
J1:2 -> J19:Vd
J1:3 -> J19:RC1
J1:4 -> J19:SO
J1:5 -> J19:SC

At least I hope.

No led is enabled on the Aout after booting the midibox and the DAC is not getting warm.
I have only J1-j19 connected so no 12-/+ V on J3

On pin 20 on the TL5630 I got 4.5V on pin 11 as well

-Aout not set in the config
4.5v on pin5, 20, 23 and 11 of the dac
-Aout set in the config
4.5v on pin2, 5, 20, 23, 11 of the dac

[6016.659] Setting AOUT:CS pin to ca. 5V - please measure now!

4.5v on pin2, 3, 4, 5 of the dac

[6016.659] Setting AOUT:CI pin to ca. 5V - please measure now!

4.5v on pin2, 3, 4, 5 of the dac

[6476.996] Setting AOUT:SC pin to ca. 5V - please measure now!

4.5v on pin2,3,4,5 of the dac

 

Does anybody has a hint what I should check?

Thanks in advance,

 

Cheers

 

Tim

Link to comment
Share on other sites

Hi Slo,

 

Thanks for the help.

From the AOUT documentation: http://www.midibox.org/dokuwiki/aout_ng

"You can leave out the TL074s for a first test. Then connect J1 to the core. Power up your Midibox. If the LED doesn't light up, IMMEDIATELY switch off power and re-check all connections and soldering."

"If the LED is on, you can now connect analog power (+/- 12V) to J3."

So I expected the led to power up, but it doesn't

I ran the tests and get:

Pin 1 VS, 2, VD

CS test J1 pin 3 high

SI test J1 pin 4 high

SC test J1 pin 5 high

So the wiring seems good.

 

Cheers

 

Tim

Link to comment
Share on other sites

Ohhh no I removed the DAC yesterday but looking back to my notes I actually had 5v on pin 5 on the dac (/PRE ).

I just learned that the flatside of the led symbol means Cathode, which is the -

So there is a high change that I have the LED connected wrongly. I mean 5v on the /PRE input should light up the LED right?

Would wrongly placing the led mean a non working aout?

If the led is wrong I will re solder the old DAC first otherwise I will bet on  a new one.

 

 

 

Screenshot from 2018-02-20 13-45-13.png

Screenshot from 2018-02-20 13-49-59.png

Link to comment
Share on other sites

Quote

I mean 5v on the /PRE input should light up the LED right? 

No, not if you installed the LED backwards. The LED only indicates power is available at the PCB, the Aout_NG would work without it. Remove the LED, test it with a 9v battery and resistor, if it lights install it the right way and if you didn't damage the DAC on removal, re-install it.

  • Like 1
Link to comment
Share on other sites

I'd very interested to hear your report and I really hope it works for you. I could not get my Aout_NG working and gave up after many tries, 1 or 2 other people have experienced the same thing after doing everything right, so your input will be welcome.

Link to comment
Share on other sites

Ok I got a new DAC.

the led is lightup.

J1 Pin 1, GND

J1 Pin 2, + 4.5V


[24708.300] Setting AOUT:CS pin to ca. 5V - please measure now!
J1 pin3   4.5v
[24683.868] Setting AOUT:CS pin to ca. 0V - please measure now!
J1 pin 3   0v
[24742.891] Setting AOUT:SI pin to ca. 5V - please measure now!
J1 pin 4   4.5v
[24755.116] Setting AOUT:SI pin to ca. 0V - please measure now!
J1 pin 4   0v
[24775.452] Setting AOUT:SC pin to ca. 5V - please measure now!
J1 pin 5   4.5v
[24790.716] Setting AOUT:SC pin to ca. 0V - please measure now!
J1 pin 5   0v

The cables seem good.

A new dac is soldered which I carefully inspected.

Now +-12v is connected to j3. 
On the TL074s +-12v is measured that is pin 4 +12v.

In bipolar mode I get about -2.6v on all 8 channels, caliaout 1 max does nothing, neither does changing the calibration voltage on the midibox itself.

I am trying to find very hard if I soldered something wrong but that it doesn't seem like that.

 

Anybody any tip what I should do?

 

Link to comment
Share on other sites

Ah I seem to have sucses.  When I disabled th aout_ng in the config, saved it and turned the midibox off. Then turned it on again, selected - aout-ng and tweaking the calibration voltages gives me output!!!! ITS ALIVE!!!

It's to bad that most likely the first dac was fine as well and this does look like a bug. (not sure)

I will continue the tests another day.

Cheers,

F*cking happy Tim

Link to comment
Share on other sites

Great that this helped at your side! :)

But for the records: currently I'm not able to reproduce this issue.

The test procedure:

  • turn on MIDIbox with unconfigured AOUT module
  • in CV page selected AOUT_NG module
  • exit CV page (so that this setting will be stored)
  • power-cycle MBSEQ
  • -> AOUT_NG properly configured and working
  • can be repeated with multiple power-cycles: AOUT_NG properly configured and working

Best Regards, Thorsten.

Link to comment
Share on other sites

Hi T,

Only 1 thing i did not mention is that I applied a bit off pressure on the tl074's so most likely i did something wrong. Maybe the contact wasn't ok before. Althought +-12v was there.

I will try if i can reproduce it on my side. But if i do than highly likely I did something wrong here.

 

Cheers

Tim

Link to comment
Share on other sites

  • 2 weeks later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...
 Share

×
×
  • Create New...