Jump to content

Sammich kits on eBay -- legit or bootleg?


gatesphere

Recommended Posts

  • 4 months later...
  • 1 year later...

 

I had been wanting to build a sammichSID for a while, but I couldn't find any PCBs or kits.

Finally I found a listing on eBay for a full kit which I've ordered, but now I'm wondering whether it's a bootleg...

eBay Listing: https://www.ebay.com/itm/Sammich-SID-synthesizer-un-assemble-DIY-KIT-SwinSID-MOS-6581-8580-SID-Station/153859268349?hash=item23d2ba1efd:g:6EsAAOSwHvpa6w-U

In the attached image you'll notice that the label near the SID jumper shows 6580/6582, as opposed to 8580/6582.

Perhaps a bad copy? 

 

IMG_0744.jpeg

Edited by dwestbury
Updated Links
Link to comment
Share on other sites

Unfortunately I can't check this so easily, because I would have to unmount the frontpanel PCB - but I don't think that such a typo would indicate a bootleg. The PCB color looks identical to the original one.

Best Regards, Thorsten.

 

Link to comment
Share on other sites

Well, I’m done with the build now and I can confirm that all the voltage checks worked out, so the PCBs seem OK...

I did have a problem with the 7809 voltage regulator and the LCD screen, but as a newbie, these were most likely my own fault.

I used MIOS to upload the v2_044 firmware, although my family has become impatient with me, so I need to break away for now.

More testing and hopefully final status tomorrow (expecting a second 6581 in the mail tomorrow as well).

 

 

Edited by dwestbury
Link to comment
Share on other sites

OK, I finished off the last few fiddly bits of the build, so now I can officially say that "It's Done" and more importantly "It Works!"

Full N00B disclosure of the areas I struggled with, include:

-Soldering ANYTHING with a larger ground connection (example voltage regulators) made a solder blob mess, until I adjusted my iron heat setting to ~750 F.

- After much troubleshooting, I realized I had to redo all of the board to board mezzanine connectors between the control surface and base PCBs. I hadn’t made them long enough to to establish good contact.

But, honestly everything else was really straight forward and it’s been a very rewarding experience to work on and play with the results.

I can’t say enough about the collective efforts hat went into the design, documentation, PIC programming, etc. a real community effort (wow).

As I’ve said elsewhere, I’m already working on a big brother MB-6582 project, so I can have multiple instruments playing at once. I know my experience with the sammichSID will come in handy...

 

...I am left wrestling with an ethical question though...

If I did actually buy a set of Chinese knockoff PCBs, is anyone getting cut out of their commission on them (i.e., Wilba, TK, nILS, etc.)? ...or are the volumes they're selling on eBay likely to be so low that it’s not really a big concern?

Thanks again everyone...

Cheers!

 

SammichSID.jpg

IMG_0757.jpeg

IMG_0759.jpeg

IMG_0762.jpeg

IMG_0760.jpeg

IMG_0758.jpeg

IMG_0761.jpeg

IMG_0753.jpeg

Edited by dwestbury
  • Like 1
Link to comment
Share on other sites

  • 5 months later...

 

Hi Dwestbury,

Thank you for sharing! I have 10 original SID's laying around here and I love to play with them in a nice synth
After I have found out that I "missed the boat" for ordering the orignal sammichSID kit, your info is very value for me
I have a question I have multible versions of the SID, I have 8 X 6581 and two  8580R5

Can I place them all without problems in the Hong Kong sammichSID?
 

I have to following SID's:

6581 CBM
6581 CBM
6581R3 4885
6581R3 4885
6581 CBM 4184
6581
6581 R3 0686
6581R4

8580R5
8580R5

MySID-small.jpeg

  • Like 1
Link to comment
Share on other sites

Ok, this is a question.

You have 1 7809 v regulator and 1 7812 (12v for 6581) by using the jumper you choose.

You always should measure your voltage after soldering your pcb (and test the jumper), so than you are save. 

However, I recommend using a SwinSID if you are a Beginner or want to be on the really save side and protect your SIDs as long as you are in the soldering/building/testing progress. And care about the advice I gave you about 6581, they are old, they are rare. It's better to use just 2 or 1 instead of them all because they are old and rare and they are kind of fragile now.

Edited by Noise-Generator
  • Like 1
Link to comment
Share on other sites

Thank you very much for your advise and don't worry I will take good care of them, and follow your advise and start with SwinSID first, I order just one Hong Kong SID clone, to try.

Hoping that maybe later I can order real sammichSID kit when there will be a new batch?

another question: does a copper of aluminium cooling block on those old SID's be a solution to keep them cool and therefore longer life span?

Link to comment
Share on other sites

I received my sammichSID from Hong Kong yesterday, It's looking very good, nice metal case, and even jumpers
I will carefully open it tomorrow and post the pictures, I ordered the black one with blue LED's , I'm very happy!

Edited by Audio Dandy
update info
  • Like 1
Link to comment
Share on other sites

  • 4 weeks later...

You can really trust this seller, he not only supplies sammichSID kits
of very high quality, he also delivers them quickly
and he is also very customer friendly.

(for example: if you specify when ordering what type of SIDs you have at home, he will configure for you
your sammichSID kit so, that you can place your SID's in it without any problems  - like "plug-and-play")

For novice MIDIbox Newbies like myself, it's really nice that there are sellers like this
exist, and given the positive reactions he already has, and also through my personal experience with him
I can advise you that you shoudn't  have to worry in this case, I would order one soon as possible before  he doesn't have them anymore ....

Edited by Audio Dandy
type error
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...
×
×
  • Create New...