Testing/Troubleshooting

1,983 topics in this forum

1. SEQ V4+ & Breakout Box - double trigger

   By rbv2, May 23, 2019
   • 13 replies
   • 5.1k views
   • 
   • rbv2
   • May 26, 2019

2. Seq v4+: Left LeMec board troubles

   By geekraver, May 18, 2025   

   • seqv4+
   • 7 replies
   • 2k views
   • 
   • forestcaver
   • May 25, 2025

3. SEQ_V2 LED's too bright...

   By Julian, February 1, 2005
   • 1 reply
   • 788 views
   • 
   • seppoman
   • February 1, 2005

4. SEQ3 freeze after 5-15 minutes, ideas?

   By creatorlars, January 19, 2008
   • 7 replies
   • 1.3k views
   • 
   • ultra
   • January 20, 2008

5. seqencer shift registers...

   By illogik, October 31, 2004
   • 4 replies
   • 1.1k views
   • 
   • illogik
   • November 5, 2004

6. sequencer reboots itself

   By ultra, April 15, 2007
   • 10 replies
   • 1.7k views
   • 
   • ultra
   • April 17, 2007

7. SEQV4 : Adding leds to gate out

   By Lamouette, October 28, 2016
   • 4 replies
   • 1.6k views
   • 
   • Lamouette
   • October 30, 2016

8. SEQV4 (wilba PCB) - SD-Card Error

   By Phatline, October 27, 2020
   • 9 replies
   • 2.9k views
   • 
   • Hawkeye
   • November 16, 2020

9. SEQV4 almost there - but not completely..

   By EsotericLabs, May 10, 2013
   • 1 reply
   • 822 views
   • 
   • EsotericLabs
   • May 10, 2013

10. seqv4 lite sd card problem (SOLVED)

    By jagzik, August 18, 2013
    • 0 replies
    • 728 views
    • 
    • jagzik
    • August 18, 2013

11. serious worry about pots

    By Fx3_hdrive, December 18, 2003
    • 5 replies
    • 1.1k views
    • 
    • Fx3_hdrive
    • December 24, 2003

12. Setting ID Header via MPLAB-(X)?

    By meltac, December 28, 2011
    • 3 replies
    • 1.3k views
    • 
    • meltac
    • December 29, 2011

13. Setting ID on multiple cores

    By Tanstaafl, January 7, 2005
    • 5 replies
    • 1.2k views
    • 
    • Tanstaafl
    • January 9, 2005

14. Setting up MB CV without Control surface?

    By Alkex, October 24, 2006
    • 2 replies
    • 702 views
    • 
    • Alkex
    • October 28, 2006

15. Setup is drawing too much current

    By NorthernLightX, February 24, 2004
    • 10 replies
    • 1.6k views
    • 
    • latigid on
    • January 30, 2010

16. Several Problems with Midibox CV

    By DerNub, September 19, 2006
    • 1 reply
    • 545 views
    • 
    • TK.
    • September 19, 2006

17. severe grounding problems

    By matrigs, May 9, 2007
    • 6 replies
    • 1.4k views
    • 
    • matrigs
    • May 10, 2007

18. SGND for the JDM Programmer?

    By banneduser, September 3, 2002
    • 2 replies
    • 1.3k views
    • 
    • TK.
    • September 3, 2002

19. Shaky Faders

    By kmifflin, September 24, 2007
    • 3 replies
    • 841 views
    • 
    • TK.
    • September 25, 2007

20. Shift between SIDs?

    By carsten_the_dane, October 10, 2006
    • 4 replies
    • 767 views
    • 
    • Wilba
    • October 19, 2006

21. Short circuit on the Pic 18F452

    By banneduser, August 12, 2003
    • 2 replies
    • 758 views
    • 
    • pilo
    • August 21, 2003

22. short circuit when clamping core J5 vss to ground

    By SounDuke, April 16, 2005
    • 1 reply
    • 611 views
    • 
    • SounDuke
    • April 16, 2005

23. short cut in a out ng

    By boops, June 7, 2009
    • 5 replies
    • 1.2k views
    • 
    • boops
    • June 14, 2009

24. shorted sammichSID -please help

    By rbv2, February 5, 2014
    • 11 replies
    • 1.6k views
    • 
    • rbv2
    • February 12, 2014

25. Shutting off an encoder?

    By Jidis, December 26, 2005
    • 2 replies
    • 805 views
    • 
    • Jidis
    • December 28, 2005