gokhan

Hello everybody, I am trying to program a simple circuit in which i can control software parameters with pots. I am trying to learn how to do this. I think it is not too much difficult to send midi data to the pc. But i don't understand what the SysEx is about? Is it not possible to make a controller wihout sysex? What i want to do is: I am going to put for example 6 pots. And each pot sends different events on channel 1. Then i will open for example Reason and then use its midi learn function to attain the pots. Is this possible? And I think when the program is closed then these parameter assignments will be lost i think. How can i store them? Thank you for your help. If these are too stupid questions i apologize but i am not an expert :)

Hi Today i tried the Pic 16F877 with a 20 MHz crystal but the problem is the same. :( Now i have "0" Voltage at Tx. Now I think something with the Pcb is wrong and i am going to make another one. Thank you Gökhan

Do u think that the PiC may be burnt or something? I tried the Rx Tx shortening and Send/Receive Sysex in Midiox, the receieved data is slightly more than the send. What does this mean? And the 7805 heats up very well. I am slowly loosing my energy :( My e-mail address is www.kavadar_15@hotmail.com, i am almost every day on msn. So I will appreciate any help :) Thank you very much Gökhan

Hello I my crystal is almost the same as in the picture above. I also have another one which is similar to the other one( short ) , i also tried that but it also didn't change anything. If we assume that the crystal is ok, then what else can be the problem? Thank You very much Gökhan

Hello Thanx for your advice, but unfortunately I dont have the opportunuty to check with an oscilloscope. Today I bought another 10 Mhz crystal and the Tx voltage was again different. (0.3. V). When I went to the electronics shop I asked for "Parallel Cut" Crystal, But they just stared me and said they do not know what it means. So is how can I know that my Crystal is paralel Cut or not? Can I maybe try the crystal with different condensers such as 22pF?? I thank you very much Gökhan

Hello I looked again; Only Core: Tx=0.5V, Rx=5V LTC Attached: Tx=3.2V, Rx=5V The other Voltages at the pins are ok. Thank you Gökhan

Hello I controlled again the voltage across the Pins. There is a Problem in pins 25 and 26. They both must be 5V. But mine is 3.16V in Pin 25 which goes to Midi Out and 0.2 V in Pin 26 which goes to Midi ?n. Thank You very much Gökhan

Hello, I do not receive the "Request for upload"....when i switch the core. 1) MAX232 is stuffed 2) Optocoupler is deconnected 3) Cable is ok 4) Checked the 5V. Ok 5) contrast is ok Shouldn't be there something going on in Midiox when I open the core. In Midiox I select the Yamaha drivers for inout and output. Then it says midi input opened and ouput opened, but only black screen after that. One thing i am not sure is that, i dont know my crystal is parallel cut. How can i check this? Thanx Gökhan

Hi I checked the JDM and now the Bootstrap loader is burnt into Pic and Verified. There is no problem. But when i turn the core on still nothing happens. In the LTC module I soldered only one 74HC00. the other ones place is empty. Can this play a role? Thank you Gökhan

Hello Everybody, I was just experimenting with the virtual midi box. I managed to control the parameters of the devices with the knobs. But i couldn't assign a midi knob to the "Stop" "Play"... buttons in Reason 2.5. Is this not possible or is there a certain way of doing it? Thank you very much Gökhan

H?, When I verify the Pic it says "Verify failed at 0000h!" . I hope that the Pic is not burnt :-\ Thanx Gokhan

Hi When turn the core on then nothing happens. In midiox nothing happens and the LCD shows only one row black boxes. I guess the Pic was not burned succesfully. But i did the troubleshooting tests and the pic was ok. I don't know what the problem can be Thank you , Gökhan

hi, the midi in port problem is now solved. I had to change the port from com3 to Com1. Now in the sysexbox i load the mios sysex file and make the device id 0000000000000100 and then press th load button. A data transfer happens but nothing changes. The lcd still shows black boxes. (I reset the box) In Midiox, the data which should appear every two seconds does not appear by me. The window is all empty. Again here when i load the sysex file, some transfer happens but nothing changes. Thank you very much Gokhan

First I want to thank you Lemonhorse for this wonderful explanation. Finally I understood it. But there is sill a problem: I installed both the Yamaha serial midi driver, when I open SysexBox then I select the yamaha ports, but there says "Midi ?n Port not ready". Im really confused with that. ;) Thanks for your help Gokhan

Hello everybody, Can somebody please explain me step by step how to load the MIOS into the Pic Through the COM port. I have JDM programmer, P?C 18F452, Core, LTC module. I am reading everyday the related pages but i still can not do it. So it would be great if you can explain me the process very simple. I thank everybody who helped so far and are going to help Best Regards, Gokhan