Jump to content

My GM5 adventure


Breeze

Recommended Posts

Hi all! A little post for the benefit of anyone jumping into the GM5 kit blind. I've been DIYing electronics for many years, but I never did SMD till now.

Having moved to Win7-64, my $1k Unitor 8 mkII suddenly became a piece of junk (so much for "many years to come", Emagic...). I heard of the GM5 looking for an alternative, and ordered 2 of the small PC boards and 2 GM5s. I had never done SMD, but it stayed on my desk for a couple of weeks while I mustered the knowledge and courage to tackle soldering this tiny chip. To make a long story short, what worked for me was:



  1. Having a 10X loupe and a magnifying lamp.
  2. Gluing the chip to the board with a tiny drop of epoxy! I couldn't get the damn thing to stop slipping after many, many tries.
  3. Using Flux! I tried going pin-by-pin flux-less, but it didn't seem to work well for me. I ended up damaging one of the traces on the board close to the GM5 and had to use a wire strand to fix it.
  4. Using the Flood and Suck Technique! Even with the flux, pin-by-pin was a PITA. So out of frustration I just flooded one side of the chip with solder, and then just used my desoldering pump to suck the excess. And it worked!!

I had this old MIDI distribution box which I chose to convert to use with the GM5. When I started mapping my extension board, it occurred to me that having LEDs would be a good thing. So I came back here to order the 5x5x5 PCB, but there were none left! So I bit the bullet and built my own: I strongly recommend anyone wanting to do this to be patient and get the 5x5x5 PCB because I spent a ridiculous amount of time hand routing a project PCB. However, the benefit of designing custom is that I added a few things:



  1. I wanted to use a dual color LED because it was easier to mount single LEDs in the box I had. Ideally, common-anode 3-pin dual-colored would have been perfect, but I only found common cathode red/green ones. So I used two additional 74HC14's to invert the LED signals for them. BTW: I did end up using a single 1/2 watt 100 ohm resistor in series with a 1k multi-turn and connected all the cathodes together through them to ground; it turns out though that the Red is slightly brighter than the green but though it isn't optimal, it's fine for the occasional checking they're useful for.
  2. I needed a couple of thru circuits so I tapped the connections of all five channels where the 6N138 connects to the 74HC14 to 2 multi-turn switches, and used another 74HC14 to get two independent 3-channel thru's whose input can be any of the 5 channels.
  3. I included a 5 volt regulator circuit for independent operation for when the computer is off. This turned out to be a useless mod because it's plugged into a powered USB hub which stays on all the time. So far it hasn't needed any additional power at all, despite the addition of 3 74HC14's and a power LED.

In the end, other than a stupid problem where one of the standoffs was touching a trace on my custom board, everything works perfectly. I had a minor issue where the name of the first port was different than the others but installing the Ploytec drivers fixed that.

A big thanks to Midibox and Ploytec for making this available. I hope some of this can help someone. It's a great little box!

Edited by Breeze
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...
×
×
  • Create New...