Seq crash issue, port selection

[lukas412]

So lately my sequencer has been crashing very intermittently and I can not reliably reproduce it. Every once in a while Ill be editing the port on a track and I will hit OSC4 and the machine will freeze, and nothing will fix it except a reboot. No error message. I can not make this happen when I try to reproduce. I have no ethernet cable hooked up. Also I am not positive that it is just OSC4 that causes or just a coincidence. I have no idea if its hardware or not. Any ideas where I can start?

 

Thanks,

 

Luke

 

[TK.]

Could you please give me your complete network configuration?

(enter "network" in MIOS Terminal, and copy&paste the output into this thread)

 

It doesn't matter if an ethernet cable is connected or not, I mainly need to know how which OSC protocol is selected for the different ports.

Maybe this helps me to reproduce the issue with some stress tests

 

Best Regards, Thorsten.

[lukas412]

Thanks TK, output below:

 

[92520.937] Loading session Maschine

[92520.938] [uIP_TASK] IP address: 192.168.1.180

[92520.938] [uIP_TASK] Netmask: 255.255.255.0

[92520.940] [uIP_TASK] Default Router (Gateway): 192.168.1.1

 

[92545.267] network

[92545.262] Ethernet cable connected: no

[92545.263] Ethernet MAC address: 00:5F:00:00:00:D4

[92545.263] Ethernet services running: yes

[92545.264] DHCP: disabled

[92545.264] IP address: 192.168.1.180

[92545.265] Netmask: 255.255.255.0

[92545.265] Default Router (Gateway): 192.168.1.1

[92545.266] OSC1 Remote address: 192.168.1.101

[92545.267] OSC1 Remote port: 8001

[92545.267] OSC1 Local port: 8000

[92545.268] OSC1 Transfer Mode: 0 - MIDI Messages       

[92545.268] OSC2 Remote address: 192.168.1.101

[92545.269] OSC2 Remote port: 8001

[92545.269] OSC2 Local port: 8000

[92545.270] OSC2 Transfer Mode: 0 - MIDI Messages       

[92545.271] OSC3 Remote address: 192.168.1.101

[92545.271] OSC3 Remote port: 8000

[92545.272] OSC3 Local port: 8000

[92545.272] OSC3 Transfer Mode: 1 - Text Msg (Integer)  

[92545.273] OSC4 Remote address: 192.168.1.101

[92545.273] OSC4 Remote port: 8001

[92545.274] OSC4 Local port: 8000

[92545.275] OSC4 Transfer Mode: 0 - MIDI Messages       

[92545.275] UDP Monitor: verbose level #0

[TK.]

The deselected DHCP is unusual (but of course allowed - seems to be the parameter which causes the problem).

Could you please check if the crash can still be reproduced with DHCP enabled?

Then I would know where to start searching.

 

Best Regards, Thorsten.

[lukas412]

Absolutely. Ill turn it on and let you know if I see the issue again.

 

thanks,

 

Luke

[lukas412]

So when I try to turn DHCP on i get this notification: "MBHP_ETH not connected"

 

I am running an LPC17 core and have it fully populated. I have the jumper wires connected and when it boots I see one red flash. Seem like a hardware issue?

 

Thanks,

 

Luke

[TK.]

Everything ok!

I've to change the message - the LPC17 doesn't use the MBHP_ETH module.

And "not connected" means for LPC17, that no ethernet cable is connected.

Keep it unconnected for this check.

 

Best Regards, Thorsten.

[lukas412]

Issue is it will not let me turn DHCP on. it just flashes the notification and it stays off.

 

LUke

[TK.]

Ok, I see...

 

Please enable it from the MIOS Terminal:

set dhcp on

store

 

Best Regards, Thorsten.

[lukas412]

Excellent that made the setting take. Ill let you know how it works out.

 

Thanks!

 

Luke