Psykhaze Posted June 2, 2016 Report Share Posted June 2, 2016 sure :D A resistor Array is much better in here , i talked without reading. my bad Quote Link to comment Share on other sites More sharing options...
latigid on Posted June 2, 2016 Report Share Posted June 2, 2016 Agreed, bent resistors suck, but you can place a 1206 in the same footprint. Look at this network from the same series: Might be interesting. Quote Link to comment Share on other sites More sharing options...
Psykhaze Posted June 2, 2016 Report Share Posted June 2, 2016 (edited) Hey that res networks sounds cool =) Edited June 2, 2016 by Psykhaze Quote Link to comment Share on other sites More sharing options...
Phatline Posted June 2, 2016 Author Report Share Posted June 2, 2016 Just now, latigid on said: Look at this network from the same series: complex - but not what aout_LC need...: aout-lc-scheme -i think- Quote Link to comment Share on other sites More sharing options...
Psykhaze Posted June 2, 2016 Report Share Posted June 2, 2016 (edited) @Phatline : It really looks quite the same than in the schematic, at least to me did not looked well . My bad once again. Edited June 2, 2016 by Psykhaze Quote Link to comment Share on other sites More sharing options...
latigid on Posted June 2, 2016 Report Share Posted June 2, 2016 @Phat You're right, I don't think it will work, sorry about that. Quote Link to comment Share on other sites More sharing options...
Psykhaze Posted June 2, 2016 Report Share Posted June 2, 2016 @Phatline I am coming back to the Accent Signal. Is it 15V Bipolar or not? Quote Link to comment Share on other sites More sharing options...
Phatline Posted June 2, 2016 Author Report Share Posted June 2, 2016 1 hour ago, Psykhaze said: @Phatline I am coming back to the Accent Signal. Is it 15V Bipolar or not? No it is in a Range from +4 to +15V (with the 4 i am not really sure), it simply feeds Q29 with Power -negative Polarity would not make sense- - the Base of Q29 is shortley triggered with the Trigger Signal - coming from Q28, Q29 now switches thru for about 1ms - with the Accent-Voltage - coming from AOUT_LC .... the other Stuff after Q29 are then is a Envelope. (as far i understand the circuit) Quote Link to comment Share on other sites More sharing options...
Psykhaze Posted June 2, 2016 Report Share Posted June 2, 2016 (edited) Sometimes some circuits are dealing with bipolar inputs by inverting the negative part, that's why i asked . So it's positive voltage feeding but not from zero and up to +15V. Thanks you for this precision =) Edited June 2, 2016 by Psykhaze Quote Link to comment Share on other sites More sharing options...
Phatline Posted June 10, 2016 Author Report Share Posted June 10, 2016 @Psykhaze here is the list of parameters for the HH+CY Frontpanel, maybe add 3 trigger LEDs? 1 Quote Link to comment Share on other sites More sharing options...
Psykhaze Posted June 10, 2016 Report Share Posted June 10, 2016 oh cool ! I was in the wiki but i'm going in illustrator right now :p Quote Link to comment Share on other sites More sharing options...
Psykhaze Posted June 10, 2016 Report Share Posted June 10, 2016 (edited) Also , good ideas about LEDs! About the mixed output, i think it would be good to have separated output for each part (HH/OH/CYM/BD/SD) in addition of the mixed one Edit : I would keep SD/BD in plugs internal and Gain pots on its specific panel Edited June 10, 2016 by Psykhaze 1 Quote Link to comment Share on other sites More sharing options...
Phatline Posted June 10, 2016 Author Report Share Posted June 10, 2016 agree with SD and BD Plugs and Gain. i would preefer Trigger LED located near Decay Pots (because the trigger is a envelope thing) individual outs > ok > so we need special plugs, which cut the conection to the mix bus - i know that most 6,3er Plugs can handle that, do you a 3,5er plug which can handle this? Quote Link to comment Share on other sites More sharing options...
Psykhaze Posted June 10, 2016 Report Share Posted June 10, 2016 you mean something like that ? : Quote Link to comment Share on other sites More sharing options...
Phatline Posted June 10, 2016 Author Report Share Posted June 10, 2016 yes but the slot should be mooved to 90° (standing) Quote Link to comment Share on other sites More sharing options...
Psykhaze Posted June 10, 2016 Report Share Posted June 10, 2016 (edited) yup,was just for concept. By the way I almost finished the frontpanel first design , i send it to you by pm very soon- I had it divided in 3 : 2 widths for Cym/HH,one central width for mix and 1 width for BD/SD. You will see the potential =)Edit:the name of such plug seems to be solder lug jack plugs> can be soldered direct on pcb : http://www.mouser.fr/ProductDetail/Kobiconn/161-MJ355W-EX/?qs=sGAEpiMZZMv0W4pxf2HiV0rxut4lN%252btKJQ4LNm5YrRs%3d Edited June 10, 2016 by Psykhaze Quote Link to comment Share on other sites More sharing options...
Phatline Posted June 10, 2016 Author Report Share Posted June 10, 2016 (edited) the Plug seems ok, when using it with extra Mix-Section (no cut off the signal path needet) my heavy modet 606... Core-Sandwitch-Conflicts Edited June 14, 2016 by Phatline 1 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.