Jump to content

Power supply for seq4 + aout_ng


jbdiver

Recommended Posts

I've got my seq4 running on a wall power supply today. I built an aout_ng board and would like to integrate it with the core32. My understanding is that I need to change the power supply to one that supports three voltages: +5V, +12V, and -12V. I'm looking for recommendations for a power supply which will meet the requirements. I'm based in the US. Here's one I found on Jameco:

http://www.jameco.com/webapp/wcs/stores/servlet/Product_10001_10001_88402_-1

Would this one work?

Link to comment
Share on other sites

This is a switching PSU with 5A for 5V supply (far too much), and 2.5 A for +12V (far too much as well)

In addition, switching PSUs are not good for analog stuff.

Unfortunately I can't give you an alternative proposal for the US (in germany we would order at "Pollin" where matching PSUs are mostly available for 5..10 EUR), but I can give you some specs:

1A for the 5V supply, only if a BLM16x16+X should be connected maybe 2A would be better.

ca. 100 mA for the +/- 12V supply

Best Regards, Thorsten.

Link to comment
Share on other sites

But: Epuisé :-/

yes i know. I can't find back its box, but the brand is ELGA.

parisian people can maybe find some in Selectronic Nation, in their backstock (maybe 2 or 3 units left)

a good trick is to cut the power plug with a dremel in order to access the 220V wires. then you fix it in the rack enclosure with screws in the 4 corners. It is molded and a pain in the ass to open

Link to comment
Share on other sites

I found a similar version of this power supply in the US -- Elpac WM113. Unfortunately it is no longer produced and doesn't seem to be available anywhere. I spent four hours searching for a suitable power supply. Unfortunately almost everything with those specs is a switching PSU which TK noted isn't good for analog.

I did find a couple power supplies which look like they might work. I don't think these are switching power supplies.

http://www.alliedelec.com/search/productdetail.aspx?SKU=8001801

This one is twice as expensive:

http://www.newark.com/sola-hevi-duty/slt12-20404-12t/power-supply-linear-5v-10w/dp/93K6609

Edited by jbdiver
Link to comment
Share on other sites

I did find a couple power supplies which look like they might work. I don't think these are switching power supplies.

http://www.alliedele...spx?SKU=8001801

according to pic : switch PSU

This one is twice as expensive:

http://www.newark.co...-10w/dp/93K6609

linear psu, so the price

I spent four hours searching for a suitable power supply. Unfortunately almost everything with those specs is a switching PSU which TK noted isn't good for analog.
the best is to make your own in this case. recycling the transformer of an old VTR is a good option, maybe using the existing circuits.

whatsoever : http://www.midibox.org/dokuwiki/doku.php?id=bipolar_12v_psu

Link to comment
Share on other sites

the best is to make your own in this case. recycling the transformer of an old VTR is a good option, maybe using the existing circuits.

whatsoever : http://www.midibox.org/dokuwiki/doku.php?id=bipolar_12v_psu

Check out this kit. It seems like it might work. It looks a little big but the price is relatively cheap:

http://www.electronickitsbychaneyelectronics.com/TRIPLE-OUTPUT-DC-POWER-SUPPLY-KIT/productinfo/C6895/

Link to comment
Share on other sites

I found a similar version of this power supply in the US -- Elpac WM113. Unfortunately it is no longer produced and doesn't seem to be available anywhere. I spent four hours searching for a suitable power supply. Unfortunately almost everything with those specs is a switching PSU which TK noted isn't good for analog.

I did find a couple power supplies which look like they might work. I don't think these are switching power supplies.

http://www.alliedelec.com/search/productdetail.aspx?SKU=8001801

This one is twice as expensive:

http://www.newark.com/sola-hevi-duty/slt12-20404-12t/power-supply-linear-5v-10w/dp/93K6609

Yeah, I use that elpac for my MBCV. Works great, hard to find though :(

Link to comment
Share on other sites

  • 3 weeks later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...
×
×
  • Create New...